Superplastic英文翻译_含义_读音_Superplastic例句

The effect of direct current pulses (DCPs) on the 7475 aluminum alloy which had underwent superplastic deformation was studied.

研究了直流脉冲电流对7475铝合金超塑性拉伸时的力学性能的影响。

In this paper, a study of the cavitation of manganese-brass during superplastic deformation is reported.

对超塑变形后锰黄铜的空洞特征进行了系统研究。

It is concluded that the decreased number of cavities is the main reason for the improved superplastic ductility.

低温预应变提高超塑性的主要原因在于它减少了变形过程中孔洞的数量。

SEM observation shows that the typical cavities are obvious in fracture surfaces of tensile samples after superplastic deformation.

利用扫描电镜观察断口发现典型的超塑性空洞形貌特征。

Nanostructured ceramics have exhibited superplastic properties at low temperatures.

纳米结构陶瓷在低温下显示出超塑性。

The optimal superplastic condition was determined by orthogonal experiment.

由正交试验法确定出最佳超塑性条件；

The outline of superplastic and anisotropic behavior in AZ91D grain refined by isothermal-rolling is summarized comprehensively.

本文综合评述了日本目前对恒温轧制微细化AZ91D板材的超塑性及其各向异性的研究情况。

The problems and trends of superplastic isothermal forming process are described.

阐述了超塑等温成形工艺现存的问题及发展方向。

Superplastic materials are sensitive to strain rate sensitivity.

超塑性材料是应变速率敏感性材料。

The fracture behaviors in superplastic deformation of 2091 Al-Li alloy have been investigated.

摘要研究了2091铝锂合金超塑变形的断裂行为。

The cavitation under the superplastic tensile has been observed through the analysis of microstructure.

并通过对组织分析，观察在相应超塑性条件下空洞形成的基本特点。

The works needed on superplastic forming of amorphous alloys are proposed based on the requirement of material forming process.

根据材料成形工艺的要求，提出了非晶合金超塑性成形研究的内容。

This part by superplastic forming process is simpler and saving material over 60% than by machin. . .

超塑性成形工艺制造该零件比原机加工工艺简单，节省材料超过60%。

In this paper, some basic issues on the superplastic deformation process of AZ31 magnesium alloy was investigated.

本文以AZ31镁合金为对象，研究了该合金在超塑性变形过程中的一些基础问题。

Grain group movement is easy found in superplastic deformation of the materials with complex microstructure.

非典型等轴细晶材料超塑变形中复杂多变的显微组织易于产生晶粒群的运动形式。

Study of a Superplastic Forming Titanium Alloy at Low Temperature and High Strain Rate

一种可在低温高应变速率下超塑成形的钛合金研究及其开发

Microstructure of a Spray-formed Ultrahigh Carbon Steel After Superplastic Deformation

喷射成形超高碳钢超塑性变形后的微观组织

Microstructures and superplastic properties of one kind of two phase titanium alloy varied with heat treatment condition

热处理对一种两相钛合金超塑性及组织的影响

Design and Implement of a Constant Strain Rate Controlled Superplastic Bulging Tester

恒应变速率超塑气胀成形试验系统的测控原理及实现

Upsetting forming pressure study of superplastic materials

超塑性材料的镦粗变形力的研究

Equipotential field simulation for the gas pressure superplastic bulging of axisymmetrical circular sheets

轴对称件超塑性气压胀形过程的等势场模拟

Superplastic Micro Deep Drawability of Nanocrystalline Nickel Sheet Fabricated by Electrodeposition

电沉积纳米镍薄板的超塑微拉深性能

Variation of Surface Roughness of a Sheet During Superplastic Deformation

板料超塑性变形时表面粗糙度演化

Finite element analysis of direct-reverse superplastic bulging process for thickness distribution controlling

控制厚度分布的正反向超塑胀形的有限元分析

Superplastic Co-Deformation Strengthening Terms of Flame Spraying Coating

表面喷熔层超塑性变形强化及其协调变形条件

Identification of Material Parameter in Constitutive Equation of Metal Superplastic Deformation

金属超塑变形本构方程中材料参数的识别

Superplastic solid-state welding of dissimilar steels under different microstructure by ultra-fining treatment

不同组织超细化预处理下的异种钢超塑焊接

Exploration Enhancing Strain Stress of Superplastic Deformation Using Pendant Hammer Type Tensile Tester

采用吊垂式拉伸试验机探讨超塑性变形速度的提高方式

Theoretical Model of Transformation Superplastic Diffusion Welding for Eutectoid Steel

共析钢的相变超塑性扩散连接

Superplastic Deformation in Fine-grained Materials and Its Study in Magnesium Alloys

细晶超塑性变形及其在镁合金中的研究现状

超塑性

adj.

n.