Pipe Line英文翻译_含义_读音_Pipe Line例句

Such valve can be used in medium, high pressure hydraulic and pneumatic pipe line of petroleum, chemical industry and power station.

本发明特别适用于石油、化工、电站等的中、高压液、气管道。

As container shipping industry is in the end of the trade pipe-line, it takes longer time from recovery to prosperity.

集装箱航运业作为贸易产业链的末端，从复苏走向繁荣的路程将更晚。

Thank you for your interest in the position of pipe-line design engineer.

谢谢您的兴趣在管道设计工程师的位置上。

The plug frame is cylindrical and communicates with a pipe line disposed inside the endoscope.

栓壳是筒形，并在嵌合状态与配置于内窥镜内部的管路连通。

Ground deformation induced by fault rupture gives a potential threat to the safety of infrastructures, pipe line systems and tunnels.

地层错动引起的基岩上覆土体变形对地表的建筑物、地下管线和隧道的安全带来潜在危险。

But to saddle the junction of the pipe line and groove cut, using manual cutting and grinding way, cutting quality, it is hard to guarantee.

但是对于马鞍形相贯线的管材及坡口切割，使用手工切割和打磨方式，切割质量就很难保证了。

In stress analysis of petrochemical pipe line, the secondary stress check is the one of basic strength check.

石化管道应力分析中，二次应力的校核是最基本的强度校核之一。

The pipe line invests are a very important part of oilfield surface project.

在油田地面工程投资中，注水管网投资占有很大比重。

This Standard is applicable to the pipe-line-distributed commercial natural gas with preliminary treatment in the gas field or oil field.

本标准适用于气田、油田采出经预处理后通过管道输送的商品天然气。

In the paper the installation procedure of process pipe line for integrated chemical fertilizer factory is introduced.

介绍了大型化肥厂工艺管道的安装过程。

In long pipe line, especially multi-undulate pipeline, the difficulty of prevention water hammer is most difficult.

在长间隔输水管线中，尤以多起伏管道水锤防护难度最大，发生水锤事故最多。

"Acoustic bridges" between the pipe line wall and the external surface of the coating.

“声学搭桥”，产生于管壁和外表包覆层之间。

prevent thoroughly measure pipe line such as coal powder pipe line , furnace negative pressure and flue negative pressure to be stop - up.

彻底防止煤粉管道炉膛负压和烟道负压测量管道的堵塞。

After installation of valve, support line; a sagging pipe line can distort the valve and cause failure.

安装阀门后，要支撑住管道：下垂的管道会使阀门产生变形而导致故障。

Prior to installation , thoroughly flush pipe line to remove any foreign matter .

在安装之前，要彻底冲洗所有管道，清除所有外在物质。

After installation of ale, support line; a sagging pipe line can distort ale and cause failure.

安装阀门后，要支撑住管道：下垂的管道会使阀门产生变形而导致失败。

Clear pipe line with pressurized steam before installation steam trap.

安装疏水阀之前应用带压蒸汽吹扫管道。

Shear stress test and shutting down calculation were studied, pipe shutting down time and pipe line restarting pressure were determined.

研究超稠油管道停输计算及静剪切应力测试，计算出管道安全停输时间和再启动压力；

Technical and Economic Analysis on Design of Production Pipe Line of C. P. P.

选煤厂生产管道设计的技术经济分析。

For on-line calibration system of flowmeter , the working fluid flow is from the petroleum pipe line itself.

体积管工作时的液流，对于流量计在线检定系统，是来自输油管线本身；

So based on knowledge and rule of Pipe-Line-Nets GIS data model, this paper provide a whole resolvent of Pipe-Line-Nets data model.

本论文在此情况下提出了基于知识与规则的管线网数据模型，该数据模型提供了管线网一体化的解决方案。

In the project of west to east gas pipe line, the CVN index are prescribed clearly that the sharpy impact energy should reach 120J, 85%.

在西气东输一线工程中，对弯管的韧性指标有明确规定，即要求夏比韧性指标为：120J，85%。

The source of pipe line secondary stress check condition is the stability condition.

管道二次应力校核条件来源于结构的安定性条件。

Before installing, flush pipe line to remove scale and debris.

在安装之前，冲洗管道，清除水垢和碎片。

Gas system: gas pipe line from the joint AT 1m from the workshop outside wall to industrial furnaces.

燃气系统：从车间外墙外1米处的接点至工业炉的燃气管道。

These results are helpful to the second west to east gas pipe line project.

该研究结果对西气东输二线工程有重要的现实意义和重大的经济价值。

It will have erosive and abrasive effects on the pipe line.

它对管线有腐蚀、磨蚀作用。

3D Solid modeling is basis of FEM analysis and pipe line interference check.

三维实体建模是进行有限元分析和空间管路干涉检查的基础。

Pipe line steel (X60~X80) and helicoids steel (ADB610D) supplied to the three gorges projects have been put into large scale production.

铸机高技术高附加值产品的比例明显提高，X60~X80管线用钢和ADB610D三峡右岸蜗壳用钢已大批量生产。

Should wipe to wash a car, not flush to wipe again behind with the pipe line.

应该擦洗汽车，而不是用水管冲洗后再擦。

用于输送液体或气体。