impellers英文翻译_含义_读音_impellers例句

Use one impeller when mixing thin materials, Use two or three impellers on thicker materials. Made of stainless steel.

搅拌稀材料用一款搅拌器，稠状液体使用两到三个搅拌器，所有的推进器均采用不锈钢材质。

the impellers of the fan is composed of at least a group of arc-shaped passage vanes with single closed lateral and axial magnification.

风机的叶轮由至少一组单侧封闭、轴向放大的圆弧型流道叶片组成。

the neighboring impellers are staggered with a certain angle along the circumferential direction.

相邻叶轮沿周向错开一定角度。

To reduce the risk of clogging the ACS550 is supplied with a special program that has been developed to help keep impellers clean.

ACS550提供了一个特别程序以减少堵塞的危险，帮助叶轮保持清洁。

The two impellers are arranged at the lower end of the axle sleeve to ensure moderate air-draft amount.

两片叶轮装在轴套下端，确保引风量适中。

The impellers are elaborately designed and made, optimized for low noise level and lower energy consumption.

叶轮经过精心设计和加工，噪声低、效率高。

Modle of a micro-flowrate high-speed centrifugal compressor(MHCC)impellers is builded and its performance is numerically studied.

建立一种空气工质微小流量高转速离心压缩机叶轮模型并对其性能进行数值模拟研究。

Results show that: for impellers with variable dimensionless outlet widths, diffusers of different scales exhibit distinct responses.

研究结果表明：叶轮出口无量纲宽度不同，扩压器尺寸的影响表现也不同。

A fan comprises a frame, motor base, impellers, flow guide parts and at least one flare opening.

一种风扇包括扇框、马达底座、叶轮、导流组件与至少一外扩部。

The folding impellers are close to enter drum or bulk tank, opens up with mixing rotation.

这款折叠推进器，仅靠滚桶或散装油罐入口，使用搅拌旋转装置打开。

Variable-pitch inducers can be fixed before impellers to lower the NPSHr of pumps efficiently.

为了有效降低泵的必须汽蚀余量，泵的吸入口可加装前置变螺距诱导轮。

The thrust coefficient of different hydrofoil impellers was experimentally studied and simulated with CFD.

对几种不同型式轴流桨的推力系数进行了实验及CFD模拟研究。

Furthermore, a unique impeller component increased the rigidity of impellers and tumbler.

独特的叶片组件结构提高了叶片和转笼的刚度。

An excessive deposit of calcium carbonate can , also block centrifugal pumps impellers and the nozzle ring of the granulation chamber.

碳酸钙罐子的过度存款，也阻塞离心的泵推进者和使成粒状室的喷嘴戒指。

Therefore, to automate the optimum design of impellers can help to improve the performance of axial flow pumps.

所以要提高轴流泵的性能，叶轮的自动优化设计很值得研究。

Stainless steel dispersion, milling, stirring and sand mill impellers.

不锈钢搅拌分散砂磨部件。

All castings are cast by resin sand, and impellers are machined with monolithic pouring technology.

齿轮为五级精度硬齿面，所有铸件均为树脂砂铸造，叶轮为整体浇注。

The centrifugal pump consists essentially of one or more impellers rotating in the center of a casting.

离心泵基本上是由一个或多个叶轮组成，叶轮可在壳体中旋转。

b. Ensure impellers on both ends are in the same direction and screw down with screws while installing.

在安装叶轮时注意两端的叶轮必须是同一方向并用螺钉紧固。

The authors study the manufacturing problem of standard impellers, and describe the geometrical model related to manufacture.

对增压器用精密母轮的制造问题进行研究，描绘出制造相关的几何模型。

Such cavitation often occurs in pumps, propellers , impellers, and in the vascular tissues of plants.

这样的气穴现象经常在水泵，螺旋桨，推进器，和植物的管状组织里出现。

The pump consists essentially of one or more impellers rotating in the center of a casing.

离心泵基本上是由泵体中心旋转的一个或多个叶轮组成。

The high strength-to-weight ratio of titanium is utilized to obtain the high tip speeds required for LH2 impellers and inducers.

高强度-重量比钛是利用以获取高尖端的速度所需的lh2叶轮和诱导。

and experiments with the same diffuser coupling different impellers are carried out.

在井用潜水泵上，将同一个导流器与不同的叶轮组合并进行了试验。

to make the roots type more efficient , eaton has modified the impellers by adding a twist to them and moving the intake port to the end.

做根类型更有效率，伊芳顿已经透过增加一次拧修改叶轮到底对他们和移动吸入港口。

If impellers revolve inversely while machine started, exchange the three-phase (A and B) of three-phase power (see Fig. 2).

开机时发现叶轮倒转，请将三相电源中的其中三相（A、B）交换即可（见图二）。

The 3 D turbulent flow in the impellers of double channel pump was simulated.

对双流道泵叶轮内3维不可压湍流流动进行了数值模拟。

Axial impellers consist of four blades at a 45o angle.

轴流叶轮由四个在45度角的叶片组成。

In addition, it is shown that impellers optimized at design point may not have good acoustic performances at off design point.

此外，还指出在设计流量下优化的叶轮不一定在非设计工况下也有良好的声学性能。

At present, the complex and irregular surface parts such as leaves and impellers are mainly machined by imported 5-axis NC centers.

目前，叶片、叶轮等复杂、不规则曲面零件的加工主要依赖进口的五轴联动加工中心来实现；